Gps Disconnect Reset Try Again Dji Spark

Support for Spark

---

FAQ

i. What material is the Spark front arm and rear arm made of?

Nylon and fiberglass.

Did this aid answer your questions?Yes / No

2. Where are the Spark'southward antennas and compass mounted to?

The compass is mounted to the shipping nose and the antennas are mounted to the belly of the shipping (both sides of the Downward Vision Organization module).

Did this help reply your questions?Yes / No

3. What are the motor model, KV value and RPM value for hovering, respectively?

The motor model is 1504, KV is 2100, and its RPM for hovering is 12000.

Did this help answer your questions?Yes / No

four. Does the Spark have dual IMU and dual compass?

The Spark is equipped with only one IMU and i compass. Also, the Spark should be placed in a six different directions for IMU calibration.

Did this aid answer your questions?Aye / No

5. What is the size of the propeller and what material is it made of?

The size of the propeller is v inch (diameter) and the material is fiberglass.

Did this help answer your questions?Yeah / No

6. What is the diagonal size of the Spark?

170 mm (refer to the bottom of the motor).

Did this assistance answer your questions?Yep / No

seven. How frequently should I supplant propellers?

If the propeller is scratched, bent, or damaged, replace it within i year.

Did this help answer your questions?Yes / No

8. How exercise I stop the motors in emergency cases?

When the app displays that there is an fault with the aircraft, you can stop the motors past pushing both sticks to the bottom inner or outer corners.

Did this assistance answer your questions?Yes / No

9. At what temperature will the fan work?

The fan will start working when the aircraft is powered on. Its speed will change with the temperature.

Did this help answer your questions?Aye / No

10. Return-to-Home Mechanism

If Return-to-Home is triggered when the aircraft is iii meters away from the Home Point, the aircraft will land immediately.
When the aircraft is between three g and 20 yard from the Home Signal, it volition render to the Dwelling house Point at the current altitude with the RTH at Electric current Altitude option enabled (the default setting in DJI GO iv) if flying at or to a higher place two.five yard. It volition arise to 2.v yard then return to home if flying lower than 2.5 m. If RTH at Current Altitude is disabled in DJI Get iv, the aircraft will land automatically when the aircraft is betwixt 3 chiliad and 20 thou from the Home Point.
If Render-to-Domicile is triggered when the altitude between the shipping and Domicile Point falls between xx to 100 meters, the aircraft volition ascend to the preset Return-to-Home Altitude and fly to the Home Point at 3 m/s with Obstacle Abstention enabled.
If the altitude between the shipping and Home Betoken is larger than 100 meters, the aircraft will ascend to the preset Render-to-Domicile Altitude and wing to the Home Signal 10 grand/due south without Obstacle Avoidance.

Did this help answer your questions?Yeah / No

i. How practise I actuate the aircraft?

In that location are 2 ways to activate the aircraft:
1. Connect the aircraft to the mobile device and activate the aircraft following the instructions in DJI GO four.
2. Click the icon on the upper correct corner and 'Scan QR Code"". Bespeak the aircraft camera to the QR lawmaking abreast SSID on the bombardment compartment, and so follow the instructions in DJI Become 4.
The main difference betwixt activating with DJI Go four and activating with QR Code is shown equally beneath:
For activating with QR Code, the aircraft will be activated start subsequently connecting to the Cyberspace. Subsequently the aircraft is activated, connect to the Spark's Wi-Fi network and gear up the aircraft parameters.
For activating with DJI Get 4, the aircraft parameters volition exist ready starting time afterward connecting to the Spark'southward Wi-Fi. And then connect to the Cyberspace earlier activation and switch to the Spark's Wi-Fi for activation.

Did this aid answer your questions?Yes / No

2. Is there a high wind warning for the Spark?

Aye. When the air current speed is larger than half-dozen m/due south, a notification indicating "Current of air is also strong" will be shown in DJI GO 4. When the wind speed is larger than nine.6 m/due south, a loftier wind warning will be displayed in DJI GO 4.

Did this help answer your questions?Yep / No

three. Why is the GPS signal weak or why does the aircraft enter the Atti fashion when the number of GPS satellites is big enough?

The compass in the aircraft may be interfered profoundly. In this case, the aircraft will enter Atti style when the number of GPS satellites is large enough. Delight avoid flying the Spark about factories, high voltage power lines, and metals, etc.

Did this assistance answer your questions?Aye / No

4. How practice I capture a panorama epitome?

There are two Pano modes:
Vertical/V mode: Three shots will be captured vertically so a vertical panorama will be composed.
Horizontal/H mode: Nine shots volition be captured and a panorama will exist composed.

Did this aid answer your questions?Aye / No

five. What is Shallow Focus?

When Shallow Focus is selected and the shutter button is pressed, an image with 1080p will be captured. So the aircraft ascends to near 15 cm and captures 15 shots. Select the shots in the playback screen and they volition be downloaded to the mobile device. An image with resolution 1440x1080 and 4:3 aspect ratio volition be composed. For Shallow Focus, the plane of focus is placed on the subject in the centre of the paradigm by default. Click the Shallow Focus icon at the lower right corner on the playback screen to focus the discipline manually. You can movement the composite paradigm upward and down on the screen to adjust the aperture.

Did this aid answer your questions?Yep / No

6. What should I pay attending to when capturing in Shallow Focus?

1. Do non motility the background and subject field after pressing the Shutter button in DJI GO 4 inside one 2nd. Annotation that the scene is layered and the discipline is different from the background. The camera tin can better focus on the subject and the image will have articulate texture. The feature does not perform well when capturing a white wall or in a snowy twenty-four hour period.
2. Note that the distance between the subject and camera is at least three meters. The optical altitude is three to ten meters.
3. Do not use the feature in loftier winds, because the aircraft cannot hover in place steadily, which may affect the composition.
4. The algorithm of the composite for Shallow Focus runs in the mobile phone, so the speed is relative to the mobile phone'due south performance.
5. The shooting speed in Shallow Focus is slower when the aircraft is connected to the remote controller than that when the aircraft is continued to DJI GO 4.
6. Y'all tin can press the shutter icon on the app to plow off Shallow Focus during shooting. The captured shots will exist stored in the SD bill of fare, but they cannot be equanimous.

Did this help answer your questions?Yes / No

vii. Why can I non compose the shots for Shallow Focus in DJI GO four?

i. When DJI Become 4 displays that the distance is far or the distance cannot be identified, change the shooting scene. Annotation that the scene is layered and the subject field is different from the background. The camera can better focus on the subject field and epitome volition have articulate texture. The characteristic does not perform well when capturing a white wall or in a snowy day.
2. When DJI Become four displays that information technology fails to capture a picture and the aircraft is connected to the app directly, there is an error with the app link. Try to play it back. If the result cannot be fixed, take the picture again. If the aircraft is connected to the remote controller, the Wi-Fi signal is weak. Information technology is recommended to switch the frequency range or aqueduct and try again.
3. When DJI Become 4 displays that the relative distance between the person and the aircraft is wrong, take the picture over again.

Did this help reply your questions?Yeah / No

i. What is the gimbal of the Spark?

It is a two-axis gimbal, providing a steady platform for the camera.

Did this assist answer your questions?Yes / No

ii. Tin I dismantle the gimbal by myself?

No.

Did this help answer your questions?Yes / No

3. Is there any indicator on the gimbal?

No.

Did this assistance reply your questions?Yeah / No

iv. What is the maximum video bitrate?

24 Mbps.

Did this help reply your questions?Aye / No

v. What'southward the controllable range of the photographic camera?

0° to -85°

Did this help answer your questions?Yeah / No

6. What'southward the minimum focus altitude of the camera?

2 m.

Did this help answer your questions?Yeah / No

vii. Does the Spark have filters?

No.

Did this help reply your questions?Yes / No

eight. What should I do if the video or paradigm transmission blurs when the shipping is braking indoors?What should I do if the video or epitome transmission blurs when the aircraft is flying outdoors at night or in a cloudy day?

The blurry issue cannot exist removed in long exposure when the Spark flies indoors, in cloudy day, or at night. The issue occurs when the exposure time is longer than 10 minutes.
You can too set the camera to Chiliad way to reduce the exposure time, but the image quality will subtract. For instance, in A mode, the shutter is 100 and ISO is 100, and so y'all tin set the shutter to 200 and ISO to 200 manually.

Did this help answer your questions?Yes / No

ix. What should I practise if the shipping shakes and moire blueprint occurs during flight?

Do not fly the Spark in the post-obit weather:
ane. Loftier winds
2. Sport manner
3. Braking in Atti mode

Did this aid answer your questions?Yes / No

ten. What should I do if the roll axis is tilted during flight?

When the aircraft enters Atti mode, the gimbal volition switch to FPV manner automatically, because the GPS indicate is lost and the Vision Positioning Arrangement is turned off. A notification stating that the flight mode is switched to Atti mode is shown on the app. In this case, the gimbal will exist tilted. To fix the issue, plough on Vision Positioning Arrangement or look until the GPS betoken is strong.
If a ""Gimbal Motor Overloaded"" warning is shown on the app, the gimbal will be powerless. To fix the effect, power on the aircraft again.

Did this assistance respond your questions?Yes / No

11. How long tin can a video be recorded with a 16G SD carte?

1080p 60 at 24 Mbps: 91 minutes

Did this help answer your questions?Yeah / No

12. What kind of SD carte du jour can exist used with the Spark?

Sandisk 16 GB UHS-1 Micro SDHC
Sandisk 32 GB UHS-1 Micro SDHC
Sandisk 64 GB UHS-1 Micro SDXC
Kinston xvi GB UHS-ane Micro SDHC
Kinston 32 GB UHS-1 Micro SDHC
Kinston 64 GB UHS-ane Micro SDXC
Samsung 16G UHS-I Micro SDHC
Samsung 32G UHS-I Micro SDHC
Samsung 64G UHS-I Micro SDXC

Did this assist answer your questions?Yes / No

13. What kind of Metering mode does the Spark back up?

Evaluative Metering and Spot Metering are supported.

Did this help answer your questions?Yes / No

14. Does the photographic camera support focus or zoom in and out?

No.

Did this assistance reply your questions?Aye / No

15. What are the photo resolution and video resolution without an SD card?

When an SD card is not inserted to the aircraft or the SD card is total, the photo resolution is 1024x768 and video resolution is 1280x720.

Did this help answer your questions?Yes / No

1. How can I link the remote controller with the aircraft by using the buttons on the remote controller?

Press the Pause Button, FN Button and C1 Button, and power on the shipping. Press and hold the Intelligent Flight Battery Switch. Release the switch when the aircraft makes a "D" sound.

Did this aid answer your questions?Yep / No

two. Can the remote controller output HDMI signal?

No.

Did this assist reply your questions?Yes / No

iii. When should I utilize the Pause Push on the remote controller?

The shipping will brake immediately when the Pause Button is pressed during flying. In this case, press the Pause Push button for iii seconds and release it. If the Pause Button is pressed when the aircraft is landing or returning to the Home Betoken, the shipping volition end landing or returning to the Home Betoken. Instead, it will brake and hover in place.

Did this aid answer your questions?Yes / No

4. Does the Spark's remote controller support Dual Remote Controller mode?

No.

Did this assistance answer your questions?Yes / No

5. Can the beeping tone of the remote controller be turned off or adjusted?

No.

Did this help answer your questions?Yes / No

6. Can I detach the antennas from the remote controller?

No.

Did this help answer your questions?Aye / No

7. Are the Spark and Mavic Pro remote controllers compatible with each other?

No.

Did this help answer your questions?Yes / No

viii. How long can a remote controller be used? How long does information technology take to fully accuse the remote controller?

It takes about two hours to fully charge the remote controller. The remote controller can piece of work for about three hours.

Did this help answer your questions?Yes / No

9. Why does the Status LED blink red slowly for 10 seconds when the remote controller is powered on?

When the remote controller is initializing, the Status LED will blink reddish slowly for 10 seconds.

Did this help answer your questions?Yeah / No

ten. Will the remote controller make a beeping audio afterward ability-on when the control sticks are not centered?

No. At that place will be a beeping sound when the battery accuse is low. If the remote controller is not connected to the aircraft and the remote controller is non used for five minutes, information technology will make a beeping for one minute and then power off.

Did this help answer your questions?Yes / No

11. What is the C1 Button used for?

You can customize the C1 Push button in the app.

Did this assistance reply your questions?Yes / No

12. What is the FN Button used for?

It is an intelligent flight shortcut button.

Did this help answer your questions?Yes / No

1. What is the resolution of the prototype transmission?

720p 30fps.

Did this assistance answer your questions?Yes / No

two. What should I do a "Disconnected" warning is shown in the app?

It means the remote controller is disconnected with the mobile device. Perform the following steps to troubleshoot this issue:
1. Cheque whether your mobile device is on the Recommended Device on dji.com.
2. Cheque whether the mobile device is connected with remote controller.

Did this assist answer your questions?Yep / No

3. What should I do if there is no image transmission but the app displays that the paradigm transmission signal is normal?

The image will be overexposed or underexposed when the Manual Exposure Mode is enabled.
Become to the Image Transmission screen, click Exposure Mode Settings, and enable Car Exposure Mode.

Did this aid respond your questions?Yes / No

4. What is the manual range?

When the shipping is connected to the remote controller:
2.4GHz:
FCC: 2000 m, CE: 500 m, SRRC: 500 m (Unobstructed, free of interference)
five.8GHz:
FCC: 2000 m, CE: 500 m, SRRC: 500 thou (Unobstructed, free of interference)
When the aircraft is connected to DJI Get 4 directly, the maximum altitude is 50 m and the maximum altitude is 80m.

Did this help reply your questions?Yep / No

5. What should I do if the aircraft cannot wing far when information technology is continued to DJI GO 4?

Delight utilize a mobile device on the Recommended Device on dji.com or a mobile device with proficient decoding performance.
Practice not shield antennas with hands. Equally the antenna for iOS device is on the upper left corner of the mobile device, it is recommended to move the Domicile Button on the mobile phone to the left.

Did this assist answer your questions?Yep / No

vi. Can I fix the aqueduct in the app when it is connected to the Wi-Fi network?

You tin set the channel to 2.4GHz or 5.8 GHz in the app. The app will automatically choose a channel. Yous tin switch the channel in the app manually.

Did this help answer your questions?Yep / No

vii. Where can I discover the Wi-Fi SSID and Password?

You can cheque the Wi-Fi SSID and Countersign inside the battery compartment or under Wi-Fi Settings in DJI Assistant 2. The original Wi-Fi SSID and Password can be plant on the foam packet box.

Did this assistance answer your questions?Yes / No

8. How can I reset or edit the Wi-Fi SSID and password?

i. Press and agree the Intelligent Flying Battery Switch for nine seconds. When the shipping makes three beeping sounds, the SSID password tin be reset. 2. When the shipping is connected to the Wi-Fi network, edit the password manually nether your telephone's Wi-Fi settings.

Did this help reply your questions?Yes / No

nine. Why can I not search the Spark'due south Wi-Fi when I turned on the mobile device?

If the aircraft has been connected to the remote controller, power on the aircraft and press and concur the Intelligent Flight Bombardment Switch for six seconds. When the aircraft makes a beeping sound, connect the aircraft to DJI Become 4. Then yous can search the Spark's Wi-Fi in your mobile device.

Did this assist answer your questions?Yeah / No

1. How long does it have to fully charge a bombardment?

80 minutes with the DJI USB charger.
52 minutes for one bombardment, 55 minutes for ii batteries and 85.2 minutes for three batteries with the battery charging hub.

Did this help answer your questions?Yep / No

2. What is the charging temperature range of the battery?

5℃ to 40℃.

Did this help answer your questions?Aye / No

3. What is the rated power of the charger?

The maximum rated power of the DJI USB charger is eighteen Westward.

Did this help reply your questions?Aye / No

4. How long shall I charge and discharge the bombardment in one case?

The bombardment needs to be charged fully once every three months.

Did this help respond your questions?Yes / No

5. What can I do if a brand new battery does non work?

The bombardment is in the sleep fashion. Information technology is recommended to connect the battery to the charger to wake it up, fully charge it and and so mount it to the aircraft.

Did this help answer your questions?Yes / No

6. How do the Bombardment Level Indicators blink if battery update failed? What can I do to fix this outcome?

The two Bombardment Level Indicators in the eye volition be solid on if battery update failed. In this example, update the battery firmware again.

Did this assist answer your questions?Yep / No

7. Is information technology normal that the bombardment level shown in DJI Become four is not 100% when the Spark is powered on with a fully charged bombardment?

It is normal every bit long as the current battery level is higher than 95% of its total power.

Did this help answer your questions?Yep / No

8. What are the functions of the button on the battery?

Power on and off the battery.
Check the battery power (press once).
Turn on Palm Launch (press twice).
Link the aircraft and remote controller (press the Break Button, FN Button and C1 Button, ability on the aircraft, release the button when the shipping makes a ""D"" sound).
Switch Wi-Fi mode (press and concur the push for half-dozen seconds and release information technology when hearing ""DD"").
Reset Spark'due south Wi-Fi (press and hold the button for nine seconds and release it when hearing ""DDD"").

Did this help answer your questions?Yes / No

one. What'due south the size of the Spark Portable Charging Station?

162mm*178mm*86mm

Did this help answer your questions?Yes / No

2. When will the Portable Charging Station turn off automatically?

When the Portable Charging Station does not detect whatsoever to-be-charged devices or the charging is complete, after 30 seconds, it will plow off automatically. The Portable Charging Station will also plough off when its ability level is less than 5%, though the charging is non consummate.

Did this help reply your questions?Yes / No

3. 3. Why does the aircraft or battery turn off when the turned on aircraft or battery is connected to the Portable Charging Station?

When the aircraft or bombardment is turned on and placed into the Portable Charging Station that is turned on for charging, the aircraft or battery volition automatically plough off.

Did this help reply your questions?Yes / No

four. Why is the battery not existence charged when it is connected to the Portable Charging Station?

If the battery is in hibernation, the Portable Charging Station volition awake the battery kickoff and charge it. If the battery is non being charged afterwards 10 seconds, effort removing the bombardment and inserting it over again.

Did this assistance reply your questions?Yes / No

5. Is the Spark Portable Charging Station h2o-proof?

No. Please avoid water when in use.

Did this help answer your questions?Yes / No

six. Is the Securing Board of the Spark Portable Charging Station removable?

No.

Did this help answer your questions?Yep / No

---

Tutorial Videos

Exporting the Flying Information

Activating the Spark by Using DJI Get 4

Resetting the Wi-Fi SSID and Password

Updating the Firmware with DJI GO 4

Updating the Remote Controller Firmware

Mounting Propeller Guards

Decision-making the Aircraft with the Remote Controller

Linking the Remote Controller

How to install the Spark'due south Intelligent Bombardment

Using the Spark Portable Charging Station

Mounting the Intelligent Flight Battery

Introduction to Shipping Modules

---

• Contact U.s.
• Downloads

CHINA

Mon-Sun 9:00 - 21:00（GMT+viii）

HONG KONG Mainland china

Mon-Sun 9:00 - 21:00（GMT+eight）

MACAU Red china

Monday-Sun nine:00 - 21:00（GMT+eight）

TAIWAN CHINA

Mon-Sun 9:00 - 21:00（GMT+8）

Nihon

Mon-Friday 10:00-17:00(GMT+9)

UNITED STATES & CANADA

Monday-Sun vii:00AM - 5:00PM (PST)

EUROPE (GERMAN)

Mon-Fri 8:00AM - five:00PM (GMT+i)

EUROPE (ENGLISH)

Monday-Fri 9:00AM - 5:00PM (GMT+1)

Britain

Mon-Fri 8:00AM - iv:00PM (GMT+0)

AUSTRALIA

Mon-Friday 9:00AM - 5:00PM (GMT+10)

BRAZIL

Mon - Fri 8:30AM - five:30PM (GMT-3)

Republic of korea

Mon-Fri ten:00AM - 7:00PM (GMT+9)

Before continuing, please log in to your account.

lawrencehazies2002.blogspot.com

Source: https://www.dji.com/support/product/spark

Share this post